Key Features

●  Two-Stage High-Pressure Industrial Pump Head: Heavy-duty two-stage cast-iron pump structure with large-size pistons and long-stroke design, realizing high-pressure compression up to 12Bar, with strong air displacement and stable performance for heavy-duty industrial continuous operation.

●  Ultra-Large Air Delivery Performance: Max air delivery reaches 1229L/min, with stable output at 60PSI and 90PSI working conditions, meeting large-flow multi-tool simultaneous industrial use demands.

●  Industrial-Grade Belt-Driven Transmission System: Large-size 480mm flywheel and 220mm motor pulley, low-speed 670r.p.m rated shaft speed, stable torque output, low motor load, wear-resistant and long service life.

●  Professional Electrical Safety Configuration: Matched with 15.0A rated current and 18.0A overload protection, 300V starting capacity supporting 20-meter long-distance power cable start-up, adapting to complex industrial power supply environments.

●  Large-Capacity 500L Pressure Vessel: CE/ASME certified heavy-duty air tank, large gas storage capacity, reducing frequent start-stop of the unit, extending continuous working time.

●  Heavy-Duty Robust Structure: Thickened steel body, heavy-duty wheeled base, suitable for harsh factory and construction site environments, strong impact resistance and durability.

●  Complete Cooling & Lubrication System: 1.6L large-capacity pump lubricating oil design, with independent large-area cooling net, efficient heat dissipation during long-time full-load operation.

●  Dual-Pressure Automatic Control: Automatic cut-in pressure at 9Bar, automatic stop at 12Bar, realizing intelligent automatic pressure control.

Expert Advice

●  Daily Maintenance: Check pump lubricating oil level regularly, maintain oil volume at 1.2-1.6L; replace special air compressor oil every 500-800 working hours; clean cooling net and air intake filter weekly.

●  Pressure Operation: Factory preset cut-in pressure 9Bar, max working pressure 12Bar; do not adjust pressure switch to exceed factory settings to avoid overload damage.

●  Power Supply Requirements: Must use 380-400V three-phase stable power supply; for power cables longer than 20 meters, use thicker-diameter cables to ensure starting voltage stability.

●  Operating Environment: Use in well-ventilated open-air or semi-open industrial areas; avoid high-temperature, dusty and humid closed environments.

●  Belt Inspection: Check belt tension and wear monthly; adjust tension in time, replace worn belts to prevent slipping and power loss.

●  Condensate Drainage: Drain condensed water from the tank bottom drain valve every 2-4 hours during continuous heavy-duty operation to prevent internal corrosion of the air tank.

●  Duty Cycle & Cooling: Under full-load 12Bar high-pressure mode, allow a 15-minute cooling break after every 40 minutes of continuous operation to protect pump and motor.

●  Mobility Safety: Depressurize the tank below 1Bar before moving; ensure the ground is flat and stable during transportation.

●  Storage Guidelines: Depressurize the tank completely, drain all moisture, clean pump and cooling net, store in a dry, dust-free and well-ventilated warehouse.

Troubleshooting Guide

FAQs

▼ What are the advantages of two-stage high-pressure design?

Two-stage compression realizes high-pressure output up to 12Bar, with larger air delivery and higher compression efficiency, suitable for high-pressure industrial applications such as sandblasting and high-pressure pneumatic tools.

▼ What scenarios is this industrial compressor suitable for?

Ideal for heavy-duty manufacturing factories, large auto repair workshops, engineering construction, sandblasting rust removal, mining auxiliary equipment, and continuous multi-tool industrial production lines.

▼ Why does it support 20-meter long-distance power cable start-up?

Equipped with 300V high starting capacity, it can adapt to long-distance power supply in large factories and construction sites, avoiding starting failure caused by voltage drop.

▼ What is the service life of this heavy-duty unit?

Industrial-grade cast-iron pump head + heavy-duty transmission structure, with standardized maintenance, the service life can reach 8-12 years, suitable for long-term continuous production.

▼ What safety standards does the tank meet?

The 500L large-capacity air tank is CE/ASME certified, complying with international pressure vessel safety standards for global industrial market access