Home page

Cyclone Z-0.28EU Aluminium alloy Monoblock Professional Air Compressor Industrial-Grade Large-Bore Dual-Cylinder Aluminium Alloy Monoblock Air Compressor with 200L Extra-Large Tank & Dual Pressure Options

Engineered for non-stop heavy-duty industrial performance and exceptional long-term durability, the Cyclone Z-0.28EU aluminium alloy monoblock professional air compressor features a powerful 3.5HP high-torque motor, ultra-large-bore dual-cylinder pump, high-strength integrated aluminium alloy monoblock construction and 200L extra-large-capacity air tank, delivering industry-leading high-volume compressed air with dual working pressure capabilities. This unit is purpose-built for large-scale manufacturing facilities, automotive service centers, heavy construction sites and continuous heavy-duty pneumatic tool operations, combining superior heat dissipation, ultra-low vibration and extended service life. Backed by Cyclone's stringent manufacturing standards, it ensures reliable round-the-clock performance even under the most demanding working conditions.

Category:

Belt Driven Compressors-(Italy Style Mono block Air Pump)

Product Inquiry

Related products

Product Details

On the technical data plate we will state following information
Name	Aluminium alloy Monoblock Professional Air Compressor
Cyclone Model NO:	Z-0.28EU
Motor Peak Power	2.5KW/3.5HP
Input Voltage:	220-240V
Air Delivery	365L/min
Pump Shaft Rated Speed	1010R.P.M
Piston Size	2*Dia.70mm
Stroke size	46mm
working pressure	8Bar /0.8Mpa/116PSI 10Bar/1Mpa/145PSI
Tank Capacity	Ce/ASME Qualified 200Lt Air Tank
Medium	Nonlethal Compressed Air

Key Features

● Industrial-Grade 3.5HP High-Torque Motor: Delivers 2.5KW peak power output, providing exceptional starting torque and rock-solid stable performance under continuous full-load heavy-duty operating conditions.

● High-Strength Aluminium Alloy Monoblock Pump: Adopts one-piece integrated aluminium alloy monoblock construction, delivering industry-leading heat dissipation performance, lightweight design and superior structural rigidity, effectively eliminating thermal deformation and significantly extending pump service life.

● Industry-Leading Ultra-High Volume Air Delivery: Achieves a consistent 365L/min air delivery, ensuring uninterrupted high-pressure airflow for multiple heavy-duty pneumatic tools operating simultaneously.

● Dual Working Pressure Capabilities: Supports both 8Bar (116PSI) and 10Bar (145PSI) maximum working pressures, adapting to a full range of pneumatic tool requirements from light maintenance to heavy industrial applications.

● 200L Extra-Large-Capacity Air Tank: CE/ASME qualified extra-thick gauge steel air tank provides massive extended air reserve, drastically reducing motor startup frequency, minimizing energy consumption and enabling prolonged continuous operation of high-demand pneumatic tools.

● Optimized Ultra-Low Speed Operation: Operates at a rated pump shaft speed of only 1010R.P.M, perfectly balanced for maximum air compression efficiency, minimal component wear, ultra-low vibration and exceptionally quiet operation.

● Ultra-Large-Bore Dual-Cylinder Design: Features 2*Dia.70mm oversized piston size with 46mm stroke length, optimized for maximum air displacement per revolution and consistent stable pressure output.

● Global Voltage Compatibility: Supports 220-240V input voltage, making it suitable for use in most countries and regions worldwide.

Expert Advice

● Daily Tank Maintenance: Always drain condensed moisture from the 200L extra-large air tank immediately after each use, especially in humid environments. For daily continuous operation, perform mid-shift drainage to prevent severe internal corrosion and ensure the highest quality compressed air.

● Dual Pressure Operation: Select the appropriate working pressure (8Bar or 10Bar) strictly according to the specific requirements of your pneumatic tools. Using higher pressure than necessary will significantly increase energy consumption and accelerate wear of all critical components.

● Lubrication Management: Check the pump lubricating oil level before each startup. Replace the pump oil every 300 operating hours to maintain optimal performance of the high-precision aluminium alloy monoblock pump.

● Pressure Safety Regulation: Never exceed the maximum working pressure of 10Bar (145PSI). Adjust the pressure regulator precisely to match your tool's requirements for optimal energy efficiency and maximum operator safety.

● Pump Maintenance: The aluminium alloy monoblock design requires minimal routine maintenance, but regular inspection of piston rings and valves is recommended to maintain the 365L/min rated air delivery performance over the long term.

● Operation Limits: Avoid continuous operation beyond the rated duty cycle to prevent motor overheating. Allow a 15-minute cooling break after every 45 minutes of continuous full-load operation.

● Storage Guidelines: When storing for extended periods, drain all moisture completely from the 200L air tank and top up the pump lubricating oil. Store in a dry, well-ventilated area away from direct sunlight and corrosive substances.

Troubleshooting Guide

Problem

Possible Cause

Recommended Solution

Compressor fails to start

1. No power supply or damaged power cord

2. Blown fuse or tripped circuit breaker

3. Faulty pressure switch

4. Motor overload protection activated

1. Check power connection and inspect cord for damage

2. Reset circuit breaker or replace fuse with correct rating

3. Test and replace faulty pressure switch

4. Allow motor to cool completely for 30 minutes before restarting

Pressure builds too slowly or fails to reach 10Bar

1. Air leaks in hoses, fittings, check valve or 200L tank

2. Worn piston rings or valves in the 70mm bore dual-cylinder pump

3. Clogged air intake filter

4. Pump shaft speed below 1010R.P.M

1. Perform a thorough leak test with soapy water and repair all leaks

2. Inspect and replace worn pump components

3. Clean or replace the air intake filter

4. Check motor operation and power supply voltage

Motor runs but no air pressure

1. Broken intake or exhaust valve in the pump2. Seized pump mechanism due to insufficient lubrication3. Damaged pump shaft or bearings4. Leaking check valve in the 200L tank

1. Inspect and replace faulty intake/exhaust valves

2. Check pump lubricating oil level and top up if necessary

3. Repair or replace damaged pump components

4. Inspect, clean or replace the leaking check valve

Excessive noise or vibration

1. Loose mounting bolts or fasteners

2. Worn motor or pump bearings

3. Unbalanced rotating components

4. Uneven placement surface

5. Low pump lubricating oil level

1. Tighten all bolts and fasteners securely

2. Replace worn bearings

3. Service or replace unbalanced components

4. Place compressor on a flat, stable reinforced surface

5. Top up pump lubricating oil to recommended level

Motor overheats

1. Continuous overload operation beyond duty cycle

2. Clogged motor cooling vents

3. Poor ventilation in operating area

4. Low pump lubricating oil level

5. Power supply voltage outside 220-240V range

1. Allow sufficient cooling breaks between operation cycles

2. Clear all obstructions from motor cooling vents

3. Move compressor to a well-ventilated open area

4. Top up pump lubricating oil

5. Ensure power supply voltage is within specified range

Air pressure drops significantly under load

1. Undersized, kinked or damaged air hoses

2. Faulty pressure regulator

3. Leaking check valve in the 200L tank

4. Total air consumption exceeds 365L/min

5. Worn pump piston rings or valves

1. Replace with appropriate large-diameter hoses and remove kinks

2. Calibrate or replace the faulty pressure regulator

3. Inspect and replace the check valve

4. Reduce the number of simultaneously operating high-demand tools

5. Inspect and replace worn pump components

FAQs

▼ What applications is this compressor suitable for?

The Cyclone Z-0.28EU 200L 3.5HP aluminium alloy monoblock compressor is ideal for large-scale manufacturing facilities, automotive service centers, heavy construction sites and continuous heavy-duty pneumatic tool operations including impact wrenches, air hammers, sandblasters, spray guns and air ratchets.

▼ What is the air delivery of this compressor?

The compressor delivers a stable industry-leading 365L/min air delivery, providing sufficient airflow for multiple heavy-duty professional applications and simultaneous operation of several high-demand pneumatic tools.

▼ What working pressures does this compressor support?

This compressor supports dual working pressure options: 8Bar / 0.8Mpa / 116PSI and 10Bar / 1Mpa / 145PSI, adapting to a full range of pneumatic tool requirements from light maintenance to heavy industrial applications.

▼ What is the pump shaft rated speed?

The pump shaft rated speed is only 1010R.P.M, optimized for maximum air compression efficiency, minimal component wear, ultra-low vibration and exceptionally quiet operation.

▼ What are the advantages of the 200L extra-large-capacity air tank?

The 200L CE/ASME certified extra-large air tank provides massive extended air reserve, drastically reducing motor startup frequency, minimizing energy consumption and enabling prolonged continuous operation of high-demand pneumatic tools.

Keywords:

small home workshop belt driven piston compressor

household hobby sandblasting compressor

piston air compressor

Phone: