Key Features

●  Revolutionary Dual-Motor Dual-Pump System: Features two independent 7.5HP heavy-duty high-torque motors and matched pump assemblies, delivering an unprecedented 1500L/min total air delivery, the highest in its class for single-phase power supply.

●  Intelligent Load-Adaptive Operation: Can operate with one or both motors simultaneously, automatically adjusting output to match air demand, significantly reducing energy consumption during light-load conditions by up to 50%.

●  Built-In Redundancy Design: If one motor requires maintenance or experiences a fault, the other motor can continue operating independently, minimizing downtime and ensuring uninterrupted production.

●  Ultra-Large-Bore Dual-Cylinder Design: Each pump features oversized 2×Dia.90mm pistons with extended 60mm stroke length, optimized for maximum air displacement per revolution and superior compression efficiency.

●  Dual Working Pressure Capabilities: Supports both 8Bar (116PSI) and 10Bar (145PSI) maximum working pressures, adapting to the full range of industrial pneumatic tool and equipment requirements.

●  500L Extra-Large Capacity Horizontal Air Tank: CE/ASME qualified extra-thick gauge steel horizontal air tank provides massive extended air reserve, drastically reducing motor startup frequency and ensuring stable pressure output even during peak demand.

●  Optimized Low-Speed Operation: Operates at a rated pump shaft speed of only 980R.P.M, perfectly balanced for maximum air compression efficiency, minimal component wear, ultra-low vibration and exceptionally quiet operation.

●  Dual Independent Cooling Systems: Each pump assembly features its own large cooling fan and finned pump head, providing superior heat dissipation and preventing overheating during continuous full-load operation.

●  High-Efficiency Belt-Drive Transmission: Two independent belt-drive systems provide smooth power transfer, excellent vibration isolation and easier maintenance compared to direct-drive models.

●  Portable Wheeled Design: Equipped with 4 heavy-duty rubber wheels and integrated lifting handles, allowing for easy relocation within large industrial facilities.

●  Global Voltage Compatibility: Supports 220-240V single-phase input voltage, making it suitable for use in most countries and regions worldwide without requiring three-phase power.

Expert Advice

●  Daily Tank Maintenance: Always drain condensed water from the multiple drain valves at the bottom of the 500L horizontal air tank immediately after each use. For 24/7 continuous operation, perform drainage every 6 hours to prevent severe internal corrosion and ensure the highest quality compressed air.

●  Dual Pressure Operation: Select the appropriate working pressure (8Bar or 10Bar) strictly according to the specific requirements of your industrial equipment. Using higher pressure than necessary will significantly increase energy consumption and accelerate wear of all critical components.

●  Dual-Motor System Maintenance: Regularly inspect both motors and pump assemblies for proper operation. Ensure both belt-drive systems have equal tension and wear characteristics for balanced performance.

●  Belt Drive Maintenance: Inspect all drive belts for wear, cracks or tension issues every 2 months. Replace the complete belt set for both pumps every 10 months for optimal power transfer and reliability.

●  Lubrication Management: Check the lubricating oil level in both pumps before each startup. Replace the pump oil in both units simultaneously every 250 operating hours to maintain balanced performance and extend service life.

●  Pressure Safety Regulation: Never exceed the maximum working pressure of 10Bar (145PSI). Adjust the pressure regulator precisely to match your equipment's requirements for optimal energy efficiency and maximum operator safety.

●  Operation Limits: Avoid continuous operation beyond the rated duty cycle. Allow a 25-minute cooling break after every 35 minutes of continuous full-load operation with both motors running.

●  Installation Guidelines: Install the compressor on a flat, level, reinforced concrete foundation at least 200mm thick. Ensure there is at least 2 meters of clear space around the unit for proper ventilation and maintenance access.

●  Mobility Safety: When moving the compressor, always use the integrated lifting handles and ensure the air tank is depressurized to below 1Bar for safe transportation.

●  Storage Guidelines: When storing for extended periods, drain all moisture completely from the 500L air tank, top up the lubricating oil in both pumps and store in a dry, well-ventilated area away from direct sunlight and corrosive substances.

Troubleshooting Guide

FAQs

▼ What are the advantages of the dual-motor dual-pump system?

The dual-motor dual-pump system provides three key advantages: 1) Unprecedented 1500L/min total air delivery for the most demanding applications; 2) Intelligent load-adaptive operation that saves energy during light-load conditions; 3) Built-in redundancy that ensures uninterrupted operation even if one motor requires maintenance.

▼ What applications is this compressor suitable for?

The Cyclone Z-1.34EU 500L 15HP dual-motor industrial belt-driven compressor is ideal for large-scale manufacturing plants, heavy industrial facilities, shipyards, mining operations, automotive assembly lines and continuous 24/7 heavy-duty pneumatic operations including sandblasting, heavy impact wrenches, large spray systems and multiple simultaneous tool operations.

▼ What is the total air delivery of this compressor?

The compressor delivers 750L/min from each pump assembly, providing a total industry-leading 1500L/min air delivery, sufficient for the most demanding industrial applications and simultaneous operation of dozens of high-demand pneumatic tools and equipment.

▼ Can this compressor operate with only one motor?

Yes, the dual-motor system is designed to operate with one or both motors simultaneously. This allows for energy-efficient operation during light-load conditions and provides built-in redundancy to minimize downtime.

▼ What is the pump shaft rated speed?

The pump shaft rated speed is only 980R.P.M, optimized for maximum air compression efficiency, minimal component wear, ultra-low vibration and exceptionally quiet operation, significantly extending the service life of all critical components.